{"id":65289,"date":"2022-10-06T10:05:48","date_gmt":"2022-10-05T23:35:48","guid":{"rendered":"https:\/\/www.solarquotes.com.au\/blog\/?p=65289"},"modified":"2023-07-13T14:37:14","modified_gmt":"2023-07-13T04:07:14","slug":"1-25x-solar-rule","status":"publish","type":"post","link":"https:\/\/www.solarquotes.com.au\/blog\/1-25x-solar-rule\/","title":{"rendered":"One Point Two Five; It’s Like Orwell’s 1984, But For Solar"},"content":{"rendered":"
\"1.25x

Image Credit: Glen Morris. Typeface & Design Credit: Beelzebub & his helpers from Standards Australia.<\/p><\/div>\n

The recently updated Australian Standard for solar installations, AS5033:2021, contains the following clause that has caused a few headaches for solar installers and designers:<\/p>\n

The PV input of DCU1<\/a><\/sup>s shall have an ISC<\/sub> PV rating of at least 1.25<\/strong> x KI<\/sub> x ISCMOD<\/sub> except where overcurrent protection is provided that is rated to protect the DCU.<\/p><\/blockquote>\n

Translation: the solar inverter<\/a> used on the solar system can’t just be rated to the calculated maximum current from the solar panels. It must be rated to 1.25x that current. This can be challenging when using modern, high-power, high-current solar panels with the solar inverters currently on the Australian market.<\/p>\n

For those who’ve been in the industry long enough, this is just the\u00a0<\/em>latest<\/i> dip and turn of the SolarCoaster. It seems there’s not a week that goes by without some insensible regulatory change, adhoc government policy or economic challenge with the potential to make those without a solar-strength constitution lose their lunch.<\/p>\n

On that note, I have noticed a few electrical contractors “getting out of solar” recently, offering job lots of leftover stock, selling panel-lifting machines and edge protection\/scaffold. The onerous compliance is getting to some people, and they’re just going back to air conditioning installs.<\/p>\n

This episode of standards pearl-clutching is a little different though, because AS5033 has been updated for 2021, and it’s only now<\/em> we’ve collectively realised a clause that was there since 2012. Unnoticed in the past, it’s now causing some heartache. Except perhaps for the Fronius<\/a> fanbois, they’re in love<\/a> all over again.<\/p>\n

Inverters Playing Catchup With More Powerful Panels<\/h2>\n

There has been a collision between the incredibly wonderful Australian Standards and the international solar energy industry. As solar panels<\/a> become ever larger, more efficient and more powerful, the current they put out is rising. Inverter manufacturers have been a little slow to adapt their offerings to match these growing PV powerhouses we put on the roof.<\/p>\n

So the upshot is that, even though they are acceptably rated under normal<\/em> conditions, some cheap inverters with lower-rated currents can’t technically be used with the newest high-power PV panels because the AS5033 calculations call for a 1.25 multiplier to address potentially abnormal<\/em> conditions.<\/p>\n

Better inverters will cope easily, but they will struggle to have PV arrays connected in parallel within the rules. When two panels are connected in parallel, the current going into the inverter doubles. Multiply the doubled current by 1.25, and you’ll breach many inverter current limits. If you can’t parallel solar panels, it gives your solar designer less flexibility to deal with challenging roof sizes and multiple orientations.<\/p>\n

If you can’t easily parallel panels, you have to keep them all in series. Series panels keep the current the same but increase the voltage with every panel added. This gives a double whammy in that it penalises those trying to build a large system under the other uniquely Australian idiocy, which is a 600 VDC ceiling on non-commercial solar power systems. We thought this particular bugbear was dealt with in the updated solar array<\/em> standard (5033), but alas, the solar inverter<\/em> standard (4777) still contains the 600 VDC obstruction. Hooray for harmonised rules.<\/p>\n

We can get around this problem by still going parallel, but using fuses in the DC wiring system. However, they are another expense to buy and install, and more importantly, they introduce an unreliable link in the chain. Thermal cycling means they -will- eventually fail.<\/p>\n

\"\"<\/p>\n

The current2<\/a><\/sup> state of play seems to be this :<\/p>\n